First if we want to back up your Wii games and play a burned games or movies, we'll need to softmod and then then install a backup manager software. What is softmodding? It's a new way to mod a Nintendo Wii which doesn't require any chips. What shall we do is to download some software onto an SD card and install them on your Wii.
It just takes only less than 5 minutes for everyone to do it. It's very common for us to buy them on any electronics store. Maybe you might have it already from mobile phone or a camera. Get it from Amazon. I recommed imElfin DVD creator. Get a blank DVD disc from Amazon. Download and install imElfin DVD creator for free. We need Wii Unlocking software to softmod your Wii. My copy of Super Mario Sluggers got stepped on so i got it from a bay of pirates, which, again, is perfectly legal if you own the game.
Okay, lets begin. Get the Files 1. Get all of the files here 2. There is an ImgBurn Installer there if you want it. Any DVDx installed must be uninstalled before preceding. Select "Advanced Install" 2b. In this step you will install a Channel called the Backup Launcher 0. The Backup Launcher 0. I will teach you how to make and run games if you have an iso that is 4. Notice the dvd -R.
I did all of the things mentioned in the guide, i installed backup launcher 0. Reply 9 years ago on Introduction. Check out my reply to looney, check out the first link I mentioned over there, they have all the answers you need.
Press "A" when prompted to begin installation. Files will begin installing, which should just take a few moments. Press "2" to finish the installation. Regardless of what you're planning on using the custom firmware for, do not press "1. Press any button on the disclaimer screen to continue. Set your installer menus. Press "A" to begin the installation, then highlight Slot and press "A" again.
This will install d2x using the settings you entered. The installation may take a little while to complete. You'll need to install it again with slightly different settings. Set your installer menus again.
This will install d2x again in Slot You'll need it installed in both slots before you can use the CFG Loader. Part 3. Plug your formatted external hard drive or flash drive into your Wii. Plug this in before you launch CFG Loader for the first time. Use the bottom USB port on the back of the Wii. If you're prompted by your Wii to format the drive, select "Cancel. Select "USB" when prompted. This will set CFG to load backups from your external hard drive or flash drive. When prompted to select your partition, you should only have one available.
Select it to continue. Ensure IOS is selected and start the program. This will launch the CFG Loader with your settings.
Save your settings. You'll want to save your device and IOS settings so you're not prompted for them each time you start: [5] X Research source Point at the bottom of the screen to open the menu. Select "Settings" and then "System. Insert a game that you want to copy into your Wii. Insert the disc and it will appear in the CFG Loader program. You'll be using this homebrew program to rip the games from your Wii and GameCube discs to your external hard drive or your flash drive.
This will open the installation screen for the game that is inserted. Click "Install. This may take a while to complete, especially for newer, larger games. Select an installed game in CFG Loader. Once you have some games installed, they'll appear in the main CFG Loader window. Select one to view details and launch it. Press "A" to launch the game. With the game selected, press "A" to start playing. You'll see some text as the game loads, and then it will start. Continue installing games.
You can keep installing games from any disc, legitimate or burned. All of the games will be added to your external hard drive or flash drive, and you won't need the discs to play them. Part 4. Consider using the USB Loader instead of burning your games. This means that a burnt disc is useless on Wiis that were made in or later. If you download games, you can copy them to the external hard drive or flash drive that your USB Loader uses and they will appear in your USB Loader program library.
You don't need to burn them just to rip them onto your Wii. Obtain some Wii game image files. If you do want to burn games to disc instead of using your USB Loader, you'll need the game image files. There are a couple of ways you can obtain these: Wii and GameCube ISO files can be downloaded from many different torrent sites. See Download Torrents for details on finding and downloading torrents. It is illegal in most areas to download games you do not own. If you followed the above methods, you can use games that you've installed to your external hard drive or flash drive with the USB Loader.
Plug the external hard drive or the flash drive into your computer and open the "games" directory. Drag the file you want to your computer. It may take a while to copy. Convert image files copied from your external hard drive or flash drive.
If you ripped games using your Wii and copied the files to your computer, you'll likely notice that the files are in WBFS format. This will need to be converted to ISO before you can burn it: Visit wbfstoiso. Run the installer after downloading it and follow the prompts. No adware will be installed. You can click the "Open" button to browse for it. Click "Convert" to begin converting the file. This may take a while to complete. Visit imgburn. Download the latest version from the ImgBurn website.
Start the ImgBurn installation process. Double-click the installer to begin the installation. Uncheck the Ask Toolbar ads while installing. After you select the location to install ImgBurn, you'll see a screen for the Ask Toolbar. Make sure to uncheck all of the boxes before proceeding. Launch ImgBurn after installing. Once the installation is finished, launch ImgBurn from the shortcut on your desktop. Select "Write image file to disc" from the ImgBurn menu. This will open the disc writer tool.
Be aware that if your Wii is newer than , the burnt discs will not work. Click the Browse button to navigate to it, or drag it into the window. Select a low write speed. To help ensure that the burn process works, select a slow writing speed such as 1X. This will result in a longer burn but will increase your chances of the disc working. Click the Burn button in the lower-left corner. This will begin writing the file to your disc. Wait for the burn to complete.
0コメント